Uneekor’s club stickers might look simple, but they unlock a world of precision for your launch monitor. These tiny reflective decals let your EYE XO or EYE XO2 track exactly what your club is doing at impact.
If your numbers feel off, or if you’re chasing that elusive perfect swing, you’ll want your club data to be as accurate as possible. That’s where these stickers earn their keep. Without them, your expensive setup is flying blind on half the story.
In this article, you’ll learn exactly what Uneekor stickers do, how to place them, why accuracy depends on them, and how to avoid wasting your time with faulty reads.
What Do Uneekor Club Stickers Actually Do?
Uneekor club stickers aren’t just shiny decals—they’re the key to unlocking true club data. If you’re wondering why your swing numbers seem off, this might be what’s missing.
How They Work with Infrared Launch Monitors
Photometric/Infrared launch monitors like the Uneekor EYE XO2 don’t guess. They calculate. But they need help to see the full picture, and that’s where the stickers come in. Each reflective decal acts like a spotlight for the system’s cameras, lighting up key motion data in the blink of an eye.
At the moment of impact, the high-speed cameras scan the clubface. Without stickers, the sensors miss vital cues, like trying to read a stop sign in the dark. But with the right sticker in the right place, you’re giving the system a crystal-clear image of how your club behaves through the strike zone.
Club Data Points Captured with Stickers
Here’s what you unlock when the stickers are properly placed and unobstructed:
- Clubhead Speed – Measures how fast your club is moving before impact. Miss this, and you’re guessing on tempo and power.
- Smash Factor – Compares ball speed to club speed. Crucial for evaluating efficiency.
- Face-to-Path Angle – Reveals if your face is open or closed relative to your swing path.
- Attack Angle – Shows whether your club is moving up, level or down when you strike the ball.
- Face Angle – Tells you where the clubface is pointing at impact: square, open or closed.
- Club Path – Maps your club’s horizontal travel: inside-out, outside-in or dead straight.
- Loft and Lie at Impact – Tracks dynamic loft and lie changes as the club compresses the ball.
- Impact Location – Pinpoints the exact strike spot on the clubface—heel, toe, low, high, center.
Each of these stats feeds your simulator’s software. Misread one, and your whole session gets skewed. But stick the sticker right, and suddenly everything snaps into focus.
Why You Might Need Uneekor’s Stickers?
You can fire up your launch monitor without stickers, but you’ll be playing a guessing game. If you’re serious about accuracy, these tiny decals aren’t optional; they’re mission-critical.
Critical for Accurate Swing Analysis
Most launch monitors show you what the ball does. Uneekor goes deeper to tell you what the club did to the ball, but only if the system can see it. Without stickers, club data gets watered down or skipped entirely. You’ll still get ball data, but it’s like watching the second half of a movie and pretending you know the plot.
Once the stickers are on and aligned, you unlock Uneekor’s real edge: visual feedback that shows where and how you struck the ball. If you’re working on shaping shots or fixing contact, this is the intel that moves the needle.
Required for Full Feature Use of Uneekor Monitors
Not every launch monitor cares about clubface data, but Uneekor does. The EYE XO, EYE XO2 and QED are designed to work best when both bar and dot stickers are placed precisely. They’ll still function without them, but you’ll be cutting the legs off your own data.
The EYE MINI, on the other hand, can estimate more than its big brothers without stickers. But if you’re swinging indoors and want full diagnostic feedback, stickers still matter.
Think of them like tires on a race car. Technically, the car might move without them. But you’re not setting any lap records that way.
Proper Sticker Placement Guidelines
You’ve got two stickers to worry about: the bar and the dot. They work as a team. Place the bar sticker horizontally across the clubface. It’s better to line it up with the 7th groove from the bottom. If your grooves are shallow or inconsistent, use the horizontal center of the face instead.
The dot sticker goes right in the vertical middle of the bar sticker. That’s your visual anchor. It should fall between grooves, not directly on one. And whatever you do, don’t place either sticker dead center on the sweet spot. You’ll end up smacking the sticker off, and your readings go dark.
Make sure the surface is dry and clean. Stickers don’t like oil, dust or old grass marks. Press firmly. All four corners need to be flat, without peeling or folding over the edge.
Common Mistakes to Avoid
Here’s what trips up most golfers:
- Crooked placement: Even a slight angle throws off club path and face angle.
- Stickers too close to the toe or heel: Uneekor’s cameras might miss them.
- Edges hanging off the clubface: Sensors won’t read what they can’t see.
- Blocked view at impact: If the ball hides either sticker, you get nothing.
That last one’s sneaky. You can line everything up right, take a perfect swing and still get blank readings if the ball shadows the stickers during contact.
Club Type-Specific Tips for Sticker Placement
Not all clubfaces play by the same rules. What works on a 7-iron may fail miserably on your driver. One sticker misaligned, and your data’s toast.
Irons
With irons, grooves give you a solid reference point. Stick the bar sticker across the 7th groove. The dot goes vertically aligned, between grooves, not on top. Most irons give you enough flat real estate, so placement is straightforward. Still, double-check the angle. A tilted sticker throws off your club path data faster than a snap hook.
Drivers and Fairway Woods
Things get trickier with woods. The curved face offers fewer visual cues. You’ll want to find the horizontal middle and aim for flat surface, not grooves. Use the crown logo or top line as a guide. Don’t let the sticker wrap over an edge or curve. If it peels mid-swing, you’ll never know why your data looks off.
Wedges
Wedges are their own beast. Deep grooves, high bounce and lots of variation. Place the bar sticker just above the 7th groove or centered where the face flattens. Don’t press into milled texture, as it kills adhesion. Wedges also tend to strike the ball lower on the face, so make sure the dot sits high enough to stay visible at impact.
Sticker Performance Issues and Troubleshooting
Misplace the bar. Angle the dot. Let a sticker curl up or get blocked at impact. Any of these will stop your Uneekor from reading club data. You’ll still see ball numbers, but club metrics vanish.
No club path. No face angle. No impact location. And that little red dot that normally shows up on screen will be gone. That’s Uneekor’s silent protest when something’s wrong.
Worse yet, feedback becomes inconsistent. One shot reads clean; the next looks like you hit it with a garden rake. Misalignment is a silent killer, and it’s hard to spot if you’re not looking for it.
Troubleshooting Tips from the Community
Golfers in forums have been there. Here’s what they recommend:
- Check if the ball is blocking the view. At impact, the ball can cover one sticker. If that happens, you get no data.
- Double-check your loft setting. A driver set to 9.5° might not match what’s in your Uneekor software. That mismatch affects camera angles and readings.
- Review your altitude settings. One user had his sim set to 32,000 ft. His data was way off. A simple setting change fixed it.
- Clean your clubface. Dirt, oil and scratches cut sticker visibility.
- Watch lighting. Too much glare or uneven light can blind the cameras.
Sometimes it’s the small stuff: One sticker edge slightly folded or a groove line misread. When in doubt, reapply, Because nothing’s more frustrating than a perfect swing and no data to prove it.
Where to Buy and What You Get?
Each pack includes 20 sheets with 20 stickers per sheet. That’s 400 total. Enough to last months of indoor sessions unless you’re grinding daily. Cost hovers between $30 and $40, which breaks down to a dime per swing if you’re hitting often.
The stickers are pre-cut, peel-and-stick, and compatible with both EYE XO and EYE XO2. You also get a simple diagram for placement reference. Some vendors bundle in quick-start guides or application videos, which helps if you’re a visual learner.
The stickers are available at multiple online stores, but we recommend getting them directly from Uneekor’s official website.
Are the Stickers Reusable?
Short answer: no. They’re single-use. Once they peel, the adhesive loses strength. Dust, fingerprints and groove wear degrade reflectivity fast. Even if they still “stick,” they won’t scan right.
You could try reusing them. Many do, but don’t blame the system when your data goes sideways. Sometimes saving a few cents costs you the whole session.
Frequently Asked Questions
Even with a complete guide, a few questions always linger. Here’s a rapid-fire set of answers to the most common ones about Uneekor club stickers, so you’re not left guessing mid-session.
Can I use third-party reflective stickers with Uneekor?
You can, but it’s a gamble. Uneekor’s software is calibrated for their specific sticker size, shape and reflectivity. Off-brand dots might reflect light differently, or not at all. That mismatch can scramble your data. If you’re chasing consistency, stick to the originals.
Do I need stickers for every club in my bag?
Not necessarily. If you’re only testing drivers or mid-irons, start there. But the moment you want full swing diagnostics across your set, you’ll need stickers on each club you use.
How do Uneekor stickers affect data in GSPro or E6?
They don’t directly change anything inside GSPro or E6. Those platforms display ball flight based on Uneekor’s input. But the quality of that input, especially club data, relies on sticker tracking. Think of stickers as your front-line scouts. Feed them bad data, and the whole chain suffers.
Is there a visual cue that shows whether the stickers are being read?
Yes. If you’re using Uneekor’s software, you’ll see a red dot appear on the impact zone of the clubface after a shot. If the red dot is not there, your stickers probably weren’t visible at impact. Either that or something blocked them (usually the ball).
Will the stickers damage my clubface over time?
Nope. They’re adhesive, not abrasive. Peel them slowly, and you won’t leave any residue. Just avoid putting them on dirty or wet surfaces, or you’ll trap gunk underneath that could scuff with pressure.
Can I leave the stickers on permanently?
You can, but they won’t last forever. Hitting balls wears them down. Dirt, moisture and sweat from your glove can dull the reflectivity. And once they stop reflecting cleanly, your launch monitor stops caring.
What should I do if club data still isn’t captured despite correct placement?
Double-check everything: sticker visibility, angle, camera lens cleanliness, software settings, even lighting in your space. If all looks good and it’s still not working, replace the stickers. One small crease or bit of lint is all it takes to throw off the system.
Final Thoughts
You bought the launch monitor. You set up the sim. You hit balls until your hands went numb. But if the club data feels off—or worse, invisible—there’s a good chance it comes down to one tiny detail: the sticker.
Get it wrong and the system guesses. Get it right and you get truth. Face angle, attack angle, impact point, etc. every number sharpens your feedback. And that feedback turns into progress.
It’s not just about sticking something shiny on your clubface. It’s about improved precision. Without proper sticker placement, even the most expensive setup is just a box of lights and wires.
So when your next shot feels pure, you’ll know the numbers are too. Unless, of course, that dot just peeled off mid-swing…
